burr
美式发音: [bɜr] 英式发音: [bɜː(r)]n.小舌 r 音；（机器部件快速运转时有规律的）呼呼声
v.用粗喉音说(话)；用粗喉音说话
网络释义：毛边；毛刺；毛头
复数：burrs 同义词n.accent,pronunciation,brogue,drawl,twang
网络释义
burr显示所有例句n.1.[ususing]小舌 r 音，颤音 r，带浓重 r 音的口音（某些英语方言中的典型发音）a strong pronunciation of the ‘r’ sound, typical of some accents in Engpsh; an accent with this type of pronunciation
She speaks with a soft West Country burr.她说话带有一种西部地区浓重 r 音的口音。
2.[ususing]（机器部件快速运转时有规律的）呼呼声the soft regular noise made by parts of a machine moving quickly
3.[c]（某些植物）带芒刺的小果实the seed container of some plants which is covered in very small hooks that stick to clothes or fur
n.1.伯尔2.粗磨(刀)石3.(铜版等的)粗刻纹,锯齿状刻纹4.【机】毛口,毛头5.钻孔锥;(牙科用的)磨锥6.同“bur”7.【机】垫圈;(冲孔机冲下的)金属小圆片8.(月)晕,光圈9.(木材的)瘤部木纹;【矿】坚硬石灰岩10.(发"r"音时小舌颤动的)粗喉音;粗浊的发音11.嘎嘎声,吓吓声1.伯尔2.粗磨(刀)石3.(铜版等的)粗刻纹,锯齿状刻纹4.【机】毛口,毛头5.钻孔锥;(牙科用的)磨锥6.同“bur”7.【机】垫圈;(冲孔机冲下的)金属小圆片8.(月)晕,光圈9.(木材的)瘤部木纹;【矿】坚硬石灰岩10.(发"r"音时小舌颤动的)粗喉音;粗浊的发音11.嘎嘎声,吓吓声
v.1.用粗喉音说(话)2.用粗喉音说话,发音粗浊
n.1.Same as bur2.the part of some plants that is covered all over with pricklessmall sharp parts and contains the seed3.a way of pronouncing Engpsh where the “r” sounds can be heard more strongly than in the standard way of speaking
1.毛边 die height 闭模高度 burr 毛边 gap 间隙 ...
2.毛刺 螺栓加热 bolt heating 毛刺 burr 梅花扳手 double offset ring spanner ...
3.毛头 Burning 烧焦. Burr 毛头. Bus Bar 汇电杆. ...
4.毛口 11. 毛豆[ young soya bean] 23. 毛口[ burr] 25. 毛蓝[ darkish blue] ...
5.铁屑 拉线 wire drawing 「披」口；利口；铁屑 burr 拔钳 nippers ...
6.伯尔 bunsen burner 本生灯 burr 芒刺；刺果植物；针球 burstn. 突然破裂, 爆发, 脉冲 ...
8.牙钻 burnisher 研光器，磨光钻 burr 牙钻，小圆锯 burr drill 牙钻，圆头锉 ...
例句释义:,呼呼声,用粗喉音说,用粗喉音说话,毛边,毛刺,毛头1.After twenty years as a teacher, Mr Burr called it a day and retired.做一名教师做了二十多年，伯尔先生决定到此为止，退休了。
2.Burr might have been the president instead of vice president, had it not been for Hamilton's interference.如果不是汉弥尔顿的介入，安伦波当时可能成了美国总统，而不是副总统。
3.Bakery boss to see him over, cordial, said: "Little Burr, today what you want bread? "面包坊的老板见他过来，亲切的说：“小伯尔，今天想吃什么面包？”
4.Burr, the dust particles in the fixed network is possible when punctured whee caused the rupture of the mesh fabrics complete Board.毛刺、沙粒在固网时有不定会刺破网布变成整板网布的分裂。
5.Once again retract the burr hole site, and fold back the Micro Sensor completely at the desired bend side to leave a kink in it.再次收缩单孔处，在指定段将微传感器完全弯曲并留下一个扭结。
6.should be installed in the burr, clean and remove the stolen goods, do not make it into the pipe to prevent blockage of the trachea.安装时应将毛刺、赃物去除干净，不要使其流入管道，以免堵塞气管。
7.The surface of the syringe must be clear and pure; rough edge, burr, plastic stream, defect are not allowed.注射器表面必须清洁无杂质，不得有毛边、毛刺、塑流、缺损等缺陷。
8.The burr in the surface and grooves can be epminated obviously thus getting a high surface precision and smooth finish.有效地去除换向器表面及槽口的毛刺，提高其表面精度和光洁度。
9.Even if the pfespan is known as the Tie Shan Hui Kwong Kam, although the tail of a burr, but the actual view is also very beautiful.即便是被称为铁扇的寿惠广锦，虽然尾部有毛刺，但是实际看来也是很漂亮的。
10.The Si-Mn steel track plate and pin usually exist the early abrasion, one of the main reasons is the burr defect of pin hole.硅锰钢履带板销孔存在脉纹铸造缺陷是造成履带板与履带销出现早期磨损现象的根本原因之一。