flange
美式发音: [flændʒ] 英式发音: [flændʒ]n.【机】法兰(盘)；凸缘；边凸缘制造机；【建】(梁)翼缘
v.在…上安装凸缘
网络释义：法兰标准；法兰盘；翻边
复数：flanges网络释义
n.1.【机】法兰(盘);凸缘;边凸缘制造机2.【建】(梁)翼缘3.(铁路轨的)宽底
v.1.在...上安装凸缘
n.1.an edge that sticks out on a wheel so that it stays in the correct position
1.法兰 Fittings 附件 Flanges 法兰 Reducers and Adapters 异径管及接头 49 ...
2.法兰标准 过滤精度 Pore size 法兰标准 Flanges 丁晴橡胶 聚四氟乙烯 金属垫片 NBR PTFE Metal Gasket ...
3.凸缘 螺纹管接头 THREADED PIPE FITTINGS 法兰系列 FLANGES 碳钢及合金钢管件 C.S&A.S PIP…
例句释义:,法兰,凸缘,边凸缘制造机,翼缘,在…上安装凸缘,法兰标准,法兰盘,翻边1.The vertical plate in the middle is known as the web, and the top and bottom plates are referred to as flanges.的截面梁需要的形状大写字母一垂直板中间被称为网上，顶部和底部钢板被称为法兰。
2.Install One Pair of Flanges flanges at least every three pipe lengths, either side of wall penetrations and at size reductions.每三个管段长度处、墙壁穿孔处及变径处应必须至少安装一对法兰。
3.The roof rail and A-pillar are formed with a tubular body portion and longitudinally extending support flanges.顶板横梁和A柱形成有管状主体部分和纵向地延伸的支撑凸缘。
4.Seat end of valve must be mated to a standard flat faced metal flange. Rubber flanges not acceptable.阀门的阀座端口必须与平面金属法兰配合。橡胶法兰是不可接受的。
5.The standard goes further to state that when used for pipe flanges, Grade B bolts require a Heavy Hex Grade A nut under ASTM A563.标准进一步去阐明，当使用为管子安装边缘，等级B螺栓要求一枚重的六角形的成绩A坚果在ASTMA563之下。
6.The top flanges must also be leveled within . 0625 " across the flange width and length before and after welding in place. "顶部翼缘在焊接之前和焊接之后的横向和纵向平整度必须小于0.0625英寸。
7.The operator should make certain that the flanges are clean and of the proper size and are properly mounted and secured.经营者应做出一定的法兰清扫，适当规模和适当的行动，
8.There should be a bpnd flange between the two flanges here. In state of freedom, stagger joint shouldn't happen.应当有盲板.处于自由状态时，不应有错口现象。
9.A steel joist or girder with short flanges and a cross section formed pke the letter I.I形金属横梁，工字梁由短翼缘和一个十字部分做成象字母I的钢制托梁或主梁
10.As a general rule, piping flanges should be concentric to pump nozzles to within the flange bolt hole clearance tolerance.管路法兰与泵口要同心，偏差不能超过法兰螺栓孔尺寸公差。